This great article further down about Natural Gas Furnace is rather informative. You should look it over.

Check our our Video

HOW TO LOCATE YOUR FURNACE

Air circulation in your home

If you have central heating, the furnace (also known as an air handler) in your home will heat your air in the winter while the blower motor circulates the air throughout your home. The AC evaporator coils for your air handler remove heat and humidity in summer. After your furnace heats or cools your air, it is then supplied to the duct system and the air begins flowing through your registers.

How many air systems run in your home?

Your thermostat is what sets the temperature in your home for your comfort. The number of thermostat(s) determine how many systems work to regulate your indoor air for heating and cooling.

Improve IAQ with Duct cleaning

Air duct cleaning can help reduce allergies from dust and other pollutants. Pollen, dust, and mold spores can get trapped in your duct work, which means that it's being continuously circulated throughout the air you breathe at home.

According to the U.S. Department of Energy (DOE), 25 to 40 percent of the energy used for heating or cooling a home is wasted. Contaminants in the heating and cooling system cause it to work harder and shorten the life of your system. Although filters are used, the heating and cooling system still gets dirty through normal use.

The National Air Duct Cleaners Association (NADCA) recommends air duct cleaning for improvement of Indoor Air Quality (IAQ). A certified duct cleaning will include cleaning of the furnace, the main trunk line [for air circulation] and all vents (including supplies and returns) each cleaned out individually.

Where is a furnace/air-handler typically located in a home?

Typically your furnace is centrally located in the home. It is usually located in an area such as a utility closet (by a cold air return), garage, attic, basement, or crawlspace; in the case of a heat-pump (a dual-system) it will be located outside of the home. When your system is run with a heat pump, it is likely a typical duct cleaning will include cleaning of evaporator coils with full system cleanings. Your furnace is usually located by other mechanical equipment such as the hot water heater, a [permanently installed] central vacuum cleaner, or a water softener, if this equipment is installed in your home.

HVAC Repairs https://www.advantaclean.com/blog/2014/november/how-to-locate-your-furnace/

Why Heating Repair is Bound To Happen When Up Keep Is Neglected

You can maintain an furnace system numerous different ways. Odds are, during wintertime months your furnace runs all day trying to keep the home warm. In fact, it is probably on more than it needs to be because it is unable to maintain an efficient atmosphere. When troubleshooting and improving the heating segment of your furnace system, there are various areas to consider.

Replace The Air Filter

This is what you typically hear people speaking about most frequently, but so few individuals take the advice and do anything about it. If there is a obstruction, you either run the chance of not disbursing heat appropriately or possibly starting a fire.When the filter gets dirty air will not flow through either which suggests the unit must work overtime and could also mean a likelihood of fire. If the system is not distributing heat effectively, it is working harder. You want eliminate any chance of fire. In both cases it is not suitable for peace of mind or your funds.

Look At The Blower

Look at your blower blades and clean them. A messy fan will work harder to blow the air around and of course use higher energy to preserve the thermostat level you set it at. Meaning that the system is overworking and costing more money to run.

Fire Damper Function

Next, focus on the fire damper to make sure it is running correctly. The fire damper explains itself so take note of this factor.

The Flex Duct

Air ducts can get damaged over time. If there are blockades or if the duct has collapsed somewhere the furnace system will think the right temp has been achieved, which will be wrong. When this happens the system works harder to do its job but will be unable to attain the right tempurature.

Make Sure The Insulation Is Secure

It is easy to overlook the insulation, but is probably the most common reason for a system malfunctioning. Take take time to look at the insulation in between the duct work and the outside to make sure it has not come loose. When this happens furnace works more than required while trying to reach optimal temperature.

Ductwork Needs To Be Connected

See that your ductwork has not become detached from other sections. These detachments may cause cracks in the airflow and result in a loss of hot air in your home, since it will be escaping through the spaces.

Return Air Inlets And Zone Dampers

Be certain to make sure return air intakes are clean and in good shape or your system will be out of kilter. Look at your dampers to verify they are in the best place. Throughout the year we may change the positioning of the damper for many reasons (i.e. getting in a tight space or making room for storage). For a properly functioning system, check to see that the dampers are in the best spot.

If these everyday jobs are more than what you are comfortable with, it may be wise to appoint a local heating service licensed for furnace and gas furnaces. There will be numerous heating specialists around you who will take care of all of this quite capably. For optimum results you could set up annual up-keep for furnace and your heating people will call every year to deal with it.

We are very drawn to Natural Gas Furnace and I'm hoping you appreciated our entry. Sharing is caring. One never knows, you may just be doing someone a favor. Thank you so much for going through it.