Have you been hunting for advise on HVAC Furnace?

Check our our Video

HOW TO LOCATE YOUR FURNACE

Air circulation in your home

If you have central heating, the furnace (also known as an air handler) in your home will heat your air in the winter while the blower motor circulates the air throughout your home. The AC evaporator coils for your air handler remove heat and humidity in summer. After your furnace heats or cools your air, it is then supplied to the duct system and the air begins flowing through your registers.

How many air systems run in your home?

Your thermostat is what sets the temperature in your home for your comfort. The number of thermostat(s) determine how many systems work to regulate your indoor air for heating and cooling.

Improve IAQ with Duct cleaning

Air duct cleaning can help reduce allergies from dust and other pollutants. Pollen, dust, and mold spores can get trapped in your duct work, which means that it's being continuously circulated throughout the air you breathe at home.

According to the U.S. Department of Energy (DOE), 25 to 40 percent of the energy used for heating or cooling a home is wasted. Contaminants in the heating and cooling system cause it to work harder and shorten the life of your system. Although filters are used, the heating and cooling system still gets dirty through normal use.

The National Air Duct Cleaners Association (NADCA) recommends air duct cleaning for improvement of Indoor Air Quality (IAQ). A certified duct cleaning will include cleaning of the furnace, the main trunk line [for air circulation] and all vents (including supplies and returns) each cleaned out individually.

Where is a furnace/air-handler typically located in a home?

Typically your furnace is centrally located in the home. It is usually located in an area such as a utility closet (by a cold air return), garage, attic, basement, or crawlspace; in the case of a heat-pump (a dual-system) it will be located outside of the home. When your system is run with a heat pump, it is likely a typical duct cleaning will include cleaning of evaporator coils with full system cleanings. Your furnace is usually located by other mechanical equipment such as the hot water heater, a [permanently installed] central vacuum cleaner, or a water softener, if this equipment is installed in your home.

HVAC Service https://www.advantaclean.com/blog/2014/november/how-to-locate-your-furnace/

Heating Repair And Seasonal Upkeep Tips

You can maintain an furnace system numerous different ways. Odds are, during winter months your heater runs all day attempting to keep the home warm. furnace systems commonly run more than needed, due to incorrect settings. When trouble shooting and optimizing your heating portion of your furnace system, there are several areas to check out.

Change The Air Filter

This is what you usually hear people talking about most often, but so few individuals take the advice and check it. When there is a obstruction, you either run the chance of not disbursing heat adequately or perhaps starting a fire.When the filter gets dirty air will not flow through either which suggests the furnace must work overtime and will also mean a likelihood of fire. If the system is not distributing heat properly, it will be working overtime. You want eliminate any chance of fire. Neither situation is good for your wallet or your peace of mind..

Try The Blower

Examine the blower blades to ensure they are clean. If there is any build-up of grime and debris, your fan will need to work overtime to blow the air around, and your furnace will be overexerting itself. Meaning that the system is over taxed and costing extra money to run.

Fire Damper Function

Next, look at the fire damper to ensure it is running acceptably. The fire damper explains itself so take note of this factor.

Look For Holes In The Flex Duct

It is possible that your ducts became damaged throughout the years for a variety of reasons. If there are obstructions or the duct has flattened anywhere the furnace system will think the correct temp has been reached, which can be wrong. When this happens the furnace works too much to do its job but is going to be incapable to attain the right temperature range.

Band Insulation

Insulation is usually missed but is perhaps the most common explanations why an furnace system malfunctions. Take take time to look at the insulation between the duct work and the outside to ensure it has not worked itself loose. When this happens furnace will work more than desired while trying to reach the best temperature.

Air Ducts Need To Be Sealed

Make sure the ductwork is connected everywhere to all sections. These detachments can cause space in the air flow and result in a loss of heated air in your house, since it is going to be leaking out through the holes.

Check For Leaks In The Return Air Inlets And The Zone Dampers

Ensure that that return air intakes are free of the dust and dirt so air can easily flow. Look at your dampers to verify that they are in the best place. Throughout the year we may change the position of the damper for many reasons (i.e. getting in a tight space or arranging for storage). Check to see that the dampers are actually in the right position too.

If these tasks are more than what you are confident with, it may be wise to hire an area heating service licensed for furnace and gas furnaces. There will be a number of heating companies around you who can care for this all quite capably. The best advice we can offer is to establish annual upkeep for this appliance.

Do you enjoy reading up on Furnace? Try leaving feedback further down. We will be delighted to see your reactions about this post. We hope to see you back again before long. Are you aware of anybody else who is truly interested in the niche? Why not promote it. We cherish your readership.